L i g h t s p e e d - 3

[Hendz]

THE FINAL CUTS FOR MONSTER LIGHTSPEED 3 ● 100% BUGSFREE!

DOWNLOADS:
1. FROM MEGAUPLOAD 49 MB
(Note that you mast turn-on your javascript in the browser before, and wait for couple seconds as the "Regular Download"-button will available to you to click)
2. FROM MEDIAFIRE - big thankz to HaryanaMotoLovers

KEY FEATURES:
● You will really know it still.
● More stable, no more bugz, no firmware "ads" displayed, sidelocking bugz eliminated.
● Uses an Original-generic APMD of 8P-Kernel with good power management.
● Implements naturally a Clockspeed of 312 MHz.
● No more Operator's Name appeared, QuadBand is okay, and Vibe-on-Touch ready in "Fingerpad"-mode of typing (all big thankz & credits to bro Shantanu).
● Indonesian-"slang"-Languagepack ready to tap too (makasih buuuanget to bro Anatanimation for his hardworking during the past).
● Listen up now to yor FM Radio, and there no need to use a headset anyway.
● All the rests are just the same as ma previous release.








Always pay attention to these my necessary notes below and you will got satisfied much in after.

● TEN-SEQUENCES TO GET THE MONSTER IS FLASHED PROPERLY:
1. Just make sure you have yor battery fully charged or, at least 60% power remained.
2. If you have yor USB cable plugged in the PC already, then unplug it first for awhile to neutralize all cached data-communications, and then re-plug it back.
3. From Setup, switch the USB-mode to "Modem".
4. Turn off the phone by long-pressing POWER button (red).
5. Detach the battery, wait for three-seconds, and attach it back to the phone.
6. Press CAMERA key, hold it still, then press POWER key, so you got the display turns in red.
7. Plug the USB cable to the phone.
8. Close the RSDLite then run it again, as you will see the RSDLite Status is "Connected..."
10. Now open the "myLIGHTSPEED-3-FINAL-BUGSFREE.SBF" and click START. Let it flash the monster til 100% finished.

● SEE THINGS APPEARED RIGHT AFTER FLASHING:
1. Don't touch anything. And don't be frighten, the "ROKR" logo will comin up yor screen
2. In couple seconds you'll see the animated "M" logo comes together with ma footprint underneath, while boot-up sound's heard loud and clear.
3. The system is in standby mode now, still don't do anything, just wait while the "circled progress icon" stops animating.
4. Watch the screen, you'll have your Operator's Name vanished on there, it's okay though.
5. Now prepare yorself for FINAL CUTS below.

● MASTER CLEAR and then MASTER RESET:
1. Tap the "Setup" icon, scroll down, then tap the MASTER CLEAR.
2. Enter the Security Code which is normally "000000" (six-times of Zero) and tap "OK" -- there while you're entering the key one by one, you must feel the vibration of the phone, so called vibra-on-touch feature. It's really working and it's true.
3. So the phone will booted up. Just wait til it's done, and back in standby mode.
4. Please repeat those steps from No.1, but now for MASTER RESET only.
5. Okay, the last action is now: Reboot yor machine for once again... and let it works its own way... wait til back in standby mode coz he will do a self automatic data-restore for all your previous Contacts, SMS, Internal Settings etc.

Well... all steps are done right by this point. Congratz !!!
The Monster's been planted on the machine in proper way, all data restored securely, faster but less battery power to take.
So you have yor machine now ready to fully operated in MAXIMUM PERFORMANCE it can!

=====
HERE'S THE ONLY 5-STEPS IF YOU NEED MORE XTREME SPEED OF THE MONSTER:
1. Get the attachment for file "overclockerz-416-520-624-mhz.zip" I've posted below and extract it.
2. Pick just one file of them named "apmd_520_520_520.apmd" which represents a set of 520 MHz clockspeed.
3. Rename that "apmd_520_520_520.apmd" to be JUST an apmd only with no extension at all, and put this file directly into your SDcard under the folder "autorun / clock". (mmc / mmca1 / autorun / clock) -- So inside your "clock" subfolder there has to be a file named apmd (of course, you will make a new subfolder "clock" at first when it doesn't exist yet)
4. Go restart your machine.
5. THAT'S IT !!! Now feel the speed while you are playin around with the menus, apps, etc.

Getting sucks coz seeing your battery drained pretty quick and got some unwanted things or even the monster ran up so crazy??? -- Hm hm, hm, simply rename that "apmd" file to be anythin else you want, like for example "apmd512" ....... then restart the phone.
Just like that??? Yea, just like that. And it's got to be back in normal like before
=====

AND LEMME SUGGEST YOU WITH MA ONLY PRIVATE BELOW, REGARDING TO MINIMIZE THE BATTERY CONSUMPTIONS:
0. Charge only the battery when it deeply weaks or the phone been dies loosing power. -- And don't try to charge it up while you're in a call though it is less powered, or you'll got yor battery to quickly pregnant by sudden which is impossible to you really!
1. Turn off the GPRS/EDGE.
2. Turn off the Bluetooth.
3. Turn off the FoxAlarm hourly time-speaking.
4. Turn off the Info Service in the Messages settings.
5. Turn off the SCREEN3 though it's so great appears animated on the screen.
6. Make slow of Network search mode.
7. Always avoid to use the top CPU-clock, i.e. 624 MHz. This is much harmfuL to yor machine after long usages and you've probably been torch yor LCD-screen and the battery unintentionally (though on some other machines might "vulnerable" with this, but I doubt it).
Use always the lower speed than that, for example 520 MHz, if you may have to. But, don't ask me bout the power consumptions taken with this.
8. Detach the battery if you're not using the phone for long time, and, REFRESH or RESTART it after 2--3 days if the phone is always (or mostly) in standby mode to wake the system up again from a "sleep".
9. If you're in vacation, travelling somewhere, or be in a very-very private with yor gals in the chamber... just turn off the Signal away. You'll see the "TIME-2-ROCK" label displayed on the mainscreen. -- So yor mates won't "signalling" you by disturb, even yor mom & dad out there

That way, yor Monster will work in relax while stepping the days. It's so safe, and conserves more battery power to live any longer than before.

If you still need more info about Battery's Special Treatment, please read this:
(originally from Shantanu at MMS.US)

Battery calibration is simply done by running it down completely until the phone shuts off by itself...
Then remove the battery, wait 10 seconds, insert again, repeat...
If the phone shuts off again in less than a few minutes you're done.
Now remove battery and hold power button for 1minute.then insert battery.dont switch on the phone. plug the charger and recharge the battery fully until itis fully charged...
then remove battery,hold power button for few seconds,insert it and switch on the phone...
yes its done......
do this initially once in 3-4months when the phone is new.then once a month after a year to gain maximum battery performance...

REMEMBER THIS WILL NOT DRAMATICALLY IMPROVE YOUR BATTERY LIFE....
BUT THIS WILL SAVES YOUR NEW ONE TO BE DEAD BEFORE AGE
DONT EXPECT MORE FOR ALREADY SWOLLEN OR DIED BATTERY...

I hope I've made maself clear bout these tips & suggestions for all, and so for the new to E6 here, specially when using ma Monster Lightspeed 3.
Thank you so much guyz, have fun with this Monster whereva you are
Best regards from me always,

[shantanu]

Nice work hendz

[Hendz]

Thank you Shan

[sambaranghosh]

Hendz i love your firmware, I have been using your old lightspeed-3 for a while.
All i can say is that the new version is great and fpad vibe on touch feels great but I REALLY MISS THE IPHONE STYLE FPAD.
Can u implement iphone fpad with vibe on touch?

[Hendz]

@Sambarang
Thankz for using mine, and yea you better LOVIT
Now I implement the original pads of Master NTA. Perhaps you can use one from bro CoLiv_Aja himself... coz when last time I use from his,,,, bro Haryana want me to NOT to...
Now I'm completely confusing which one I'm gonna work with

Well here's ma hint if you wanna do it yorself by using of bro CoLiv:iPad styleskin, just download my attachment below. I've modified it to vibrated-on-a-touch as well.
Then do these 5 steps:
1. On yor SDcard, make a folder named "newfpad" in autorun, so it should be ---> mmc / mmca1/ autorun / newfpad
2. Just drop all extracted files right away on that "newfpad" folder
3. Now reboot yor machine.
4. GOT IT !!! Feel now the iPhone Pad style !
5. Kindly click the button THANKS in this thread to me okay

Hope that works fine to you too

[kundancool]

Nice work dude

[antzhony]

so this new LS3 is more improve then the first one?

im getting firmware expired again when i restore with smart assist.

the qei lock seems stuck too. when u unlock it u need to refresh if u want to lock the phone again.

[Hendz]

Mine is runnin smooth with this release since a week. I got no more "firmware ads" issues on ma screen.
Then try this one if you want, and read carefully too to what I've written above to get max performance.

But I don't got any idea yet for right now bout qeiLOK as I rub it out of ma monster already since on 2nd Release.
Then you should search on "E6 Applications" section forum bout qeiLOK, or, you can start by here --> http://www.motorolafans.com/forums/e...pdate-1-a.html
There if you still unable to find qeiLOK working perfectly on it, then I suppose that this apps could NOT anymore match with 8P-kernel based monster which I'm currently using......

[jackalex]

working great till now ..i did not check the fw as a whole nyway by 2morow let u know ...bro...

[sambaranghosh]

@Sambarang
Thankz for using mine, and yea you better LOVIT
Now I implement the original pads of Master NTA. Perhaps you can use one from bro CoLiv_Aja himself... coz when last time I use from his,,,, bro Haryana want me to NOT to...
Now I'm completely confusing which one I'm gonna work with

Well here's ma hint if you wanna do it yorself by using of bro CoLiv:iPad styleskin, just download my attachment below. I've modified it to vibrated-on-a-touch as well.
Then do these 5 steps:
1. On yor SDcard, make a folder named "newfpad" in autorun, so it should be ---> mmc / mmca1/ autorun / newfpad
2. Just drop all extracted files right away on that "newfpad" folder
3. Now reboot yor machine.
4. GOT IT !!! Feel now the iPhone Pad style !
5. Kindly click the button THANKS in this thread to me okay

Hope that works fine to you too

Thanka a lot Hendz. You are very helpful. Problem is that I cant find the thanks button anywhere