[Bruceleroy]

Does anyone have this working? If so can you spread the love.

I have everything setup but I need the dial commands to enter into wvdial.config. The pc tries to connect but I get errors on initialization of the modem for dialing.

Thanks,
Ubuntu 7.04

[elboby]

I have the same problem...with wvdial...
I tried to use GPRS EASY CONNECT but with problems too....

[jfsx]

Check this out:

This is from raju a member of this forum

http://wiki.kandalaya.org/cgi-bin/tw.../MotorolaA1200

So then I asked this:

jfsx wrote:
Thank you very much Raju, I've found a very nice well written and easy to follow guide in your wiki.

However I would like to know how can I use my phone as a modem in linux, could you please post a howto, I know you have tested with great results.

Thanks in advance,

Here is Raju's response:

Well, this should be fairly standard. If you're connected over USB, make sure the phone Setup is set to USB as Modem and connect the cable to the computer. With my computer the phone shows up at ttyACM0, and you can use /dev/ttyACM0 with your favourite dialer program (wvdial, minicom, etc.) to make data calls from the phone.

You could probably do the same with Bluetooth connectivity too. Use /dev/rfcomm0 (or rfcomm1 or whatever) as the modem device in your dialer.

So, this works with the following AT commands posted by Phenomenom, thanks!!!

Phenomenon wrote:
ah, lol, it's cool but thanks for that.

Well, I'm using a Palm TX and what I needed to use for the Palm TX was a script that went into the settings of the GPRS connection. I am using the T-mobile WAP plan workaround though.

Send: AT&F0&DZ&E0
Send CR:
Send: ATV1W1595=47
Send CR:
Send: AT&K3
Send CR:
Send: AT+CGDCONT=1,"IP","WAP.VOICESTREAM.COM" <----Change this
Send CR:
Send: ATD*99#
Send CR:
End

It took me a while to find that, but it was on the Howardforum.

If you tell me the service you are trying to connect to and the model of the Zaurus I'll gladly search and see what I can find. Sorry I couldn't be of more help.

Just change the bold address below with your Service provider APN

Haven't tested and I'm not sure of changing that address, but you should try[/i]

[Bruceleroy]

I am getting close. It opens a gateway with my phone but it will not stay connected. Here is the log from wvdial. Any Ideas?

I can see that it is transmitting and receiving data but it is not getting an ip from cingular.

--> WvDial: Internet dialer version 1.56
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATX3
ATX3
OK
--> Sending: ATZ
ATZ
OK
--> Sending: AT+CGDCONT=1,"IP","isp.cingular"
AT+CGDCONT=1,"IP","isp.cingular"
OK
--> Modem initialized.
--> Sending: ATM1L3DT*99***1#
--> Waiting for carrier.
ATM1L3DT*99***1#
CONNECT
--> Carrier detected. Waiting for prompt.
~[7f]}#@!}!}!} }<}!}$}%\}"}&} } } } }#}$@#}%}&r}#} } }'}"}(}"(a~
--> PPP negotiation detected.
--> Starting pppd at Wed Jul 25 10:03:18 2007
--> Pid of pppd: 8846
--> Using interface ppp0
--> Disconnecting at Wed Jul 25 10:03:26 2007
--> The PPP daemon has died: A modem hung up the phone (exit code = 16)
--> man pppd explains pppd error codes in more detail.
--> Try again and look into /var/log/messages and the wvdial and pppd man pages for more information.

[elboby]

@jfsx: thanks!!!

@Bruceleroy:I tried and had the same error:

The PPP daemon has died: A modem hung up the phone (exit code = 16)

...

[Bruceleroy]

I fixed the problem!!!!!!

*Unrelated (I installed Kppp. Nice DUN gui with alot of features)*

Seems strange but I found this on another forum and it worked!!

Add the following commands to:

/etc/ppp/options

novj
:192.168.0.254

Save the file and connect. Pretty good speed too....

I will post a how to if anyone needs it.

Edit: I have attached a how-to file.

[jfsx]

Thank you very much Bruceleroy!!!

mishcka,

you could try this for your sharp zaurus, hope this helps